Lab 3 · SG13G2Devices in weak inversion
Goal. Characterise the SG13G2 devices you will design with: gm/ID lookup tables, flicker noise against gate area, and the HBT against the MOSFET as an input device. Labs 4 and 5 reuse the tables. Goes with Chapters 5 and 6.
Run. With Docker and the container of the set-up:
python labs/spice/sg13_char.py
The script writes a .spiceinit that loads the PSP and resistor models, generates the netlists, runs them in the container with ngspice -b and parses the results (Chapter 30). It runs at the typical corner and 27 °C:
- gm/ID sweeps of
sg13_lv_nmosandsg13_lv_pmos, W = 10 µm, L = 0.5, 1 and 4 µm, |VDS| = 0.6 V; - the input-referred noise of both devices at |ID| = 1 µA for W/L = 10/1, 40/4 and 100/10 µm;
- IC and IB against VBE of the
npn13G2HBT at VCE = 0.6 V, and its input-referred noise at IC = 1 µA.
The results go to figsrc/data/sg13_gmid.csv, sg13_noise.csv, sg13_hbt.csv and sg13_hbt_noise.csv, the files that the Chapter 5 figures are drawn from. If your container reproduces them, your set-up is right.
Expected results.
| Quantity | Value | Where in the text |
|---|---|---|
| Slope factor n; gm/ID in deep weak inversion | 1.22; 31.7 V⁻¹ | Section 5.1 |
| Specific current Ispec per square, NMOS / PMOS | 0.78 / 0.20 µA | Section 5.1 |
| Thermal noise at 1 µA in weak inversion | 18.5 nV/√Hz | Section 5.2 |
| Flicker coefficient K, NMOS / PMOS | 1.6 × 10⁻¹⁰ / 5.4 × 10⁻¹⁰ V²·µm² | Section 5.3 |
| Gate area per device for 1 µVrms unchopped, NMOS | about 1800 µm² | Section 5.3 |
| HBT at 1 µA: gm/IC, β, input noise | 37.7 V⁻¹, about 680, 15.1 nV/√Hz flat | Section 5.4 |
In these models the NMOS has less flicker noise than the PMOS, the opposite of the usual rule, which is why Open-BioAFE uses NMOS input devices.
Questions.
- Build a lookup function
gm_id(ic)fromsg13_gmid.csvand use it to size an NMOS input pair for gm = 30 µS at 1 µA per device. What W/L comes out at L = 1 µm and at L = 4 µm, and what is the gate capacitance of each? - Plot the measured input noise against 1/(W·L) at 1 Hz. Is it a straight line? Extract K yourself and compare with the table.
- At what source resistance does the HBT’s base shot noise make it noisier than the MOSFET? Compare with the electrode impedances of Chapter 3.
- Add the ss and ff corners and 85 °C to the script. How much do n, Ispec and K move? Which number in your design is most sensitive?
- From the PDK’s mismatch coefficients (AVT = 3.9 mV·µm for the NMOS), find the input-pair offset for the 1800 µm² devices, and say why chopping makes it irrelevant (Chapter 9).
Deliverable. gm/ID lookup tables for both devices at three lengths, flicker noise against gate area, and a one-paragraph choice of input device for the LNA of Lab 4.
All labs · Previous: Lab 2. Electrodes and interference · Next: Lab 4. The Harrison LNA