Appendix BReference Tables
The numbers the chapters design with, collected in one place. The biosignal and electrode values are the ones in labs/python/biosig.py, so the labs use them too.
B.1Biosignals
Table B.1. Amplitude and bandwidth of the biopotentials. Orders of magnitude from the sources of Chapter 2; sources differ by a factor of a few, so treat these as design ranges. The same values are SIGNALS in biosig.py.
| Signal | Amplitude | Bandwidth | Typical sample rate |
|---|---|---|---|
| ECG (surface) | 0.5–4 mV | 0.05–150 Hz | 500 S/s |
| EEG (scalp) | 5–300 µV | 0.5–100 Hz | 256 S/s |
| EMG (surface) | 50 µV–5 mV | 10–500 Hz | 2 kS/s |
| EOG | 10 µV–3.5 mV | 0.05–50 Hz | 250 S/s |
| ECoG | 10–500 µV | 0.5–500 Hz | 2 kS/s |
| LFP (intracortical) | 50 µV–2 mV | 0.5–300 Hz | 1 kS/s |
| Spikes (extracellular) | 50–500 µV | 300 Hz–7 kHz | 30 kS/s |
B.2Electrodes
Table B.2. Electrode models. A series resistance \(R_\mathrm{s}\) and a parallel \(R_\mathrm{p}\)–\(C_\mathrm{p}\) interface, or a constant-phase element for implanted microelectrodes (Chapter 3). The wet values are the 51 kΩ‖47 nF network of the ECG standards.
| Electrode | Model | |Z| at 50 Hz | Half-cell / offset |
|---|---|---|---|
| Wet Ag/AgCl | 1 kΩ + 51 kΩ ‖ 47 nF | 41.5 kΩ | 0.222 V; ±300 mV differential offset to tolerate |
| Dry | 5 kΩ + 1 MΩ ‖ 4.7 nF | about 560 kΩ | drifts with sweat and pressure |
| Implanted micro | 10 kΩ + constant-phase element, n = 0.85 | 500 kΩ at 1 kHz | charge-injection limits apply |
B.3IHP SG13G2 device data
Table B.3. SG13G2 numbers used in this tutorial. From ngspice simulations of the IHP-Open-PDK models at the typical corner and 27 °C (labs/spice/), and from the PDK’s mismatch coefficients.
| Quantity | Value | Chapter |
|---|---|---|
| Slope factor n; gm/ID in weak inversion | 1.22; 31.7 V⁻¹ | 5 |
| Specific current per square, NMOS / PMOS | 0.78 / 0.20 µA | 5 |
| Thermal noise of a MOSFET at 1 µA | 18.5 nV/√Hz | 5 |
| Flicker coefficient K, NMOS / PMOS | 1.6 × 10⁻¹⁰ / 5.4 × 10⁻¹⁰ V²·µm² | 5 |
| Pelgrom AVT, NMOS / PMOS | 3.9 / 2.2 mV·µm | 5 |
| Pelgrom Aβ, NMOS / PMOS | 0.5 / 0.33 %·µm | 5 |
| MIM capacitor density; matching; smallest cell | 1.5 fF/µm²; 1 %·µm; 1.14 × 1.14 µm² (1.95 fF) | 17 |
| Gate capacitance in weak inversion | about 2.2 fF/µm² | 8 |
| npn13G2 at 1 µA: gm/IC, β, input noise | 37.7 V⁻¹, about 680, 15.1 nV/√Hz | 5 |
| Gate leakage, 250/4 µm NMOS: thin / thick oxide | 3–25 pA / about 10⁻²⁰ A | 5, 8 |
| Flicker noise, thick-oxide NMOS | about 2.7 × the thin-oxide power at equal area | 5, 8 |
| Pseudo-resistor near 0 V: one / four thin-oxide pairs | 2 × 10¹¹ / 7.6 × 10¹¹ Ω | 8 |
| Pseudo-resistor, one thick-oxide pair, 27 °C | 5.6 × 10¹³ Ω | 8 |
| Core supply; thick-oxide supply | 1.2 V; 3.3 V | 30 |
B.4Patient-current limits
Table B.4. Patient leakage and auxiliary current limits, summarised from IEC 60601-1 [41]. Above 1 kHz the AC limits rise in proportion to frequency, up to 100 kHz, but never above 10 mA. Always work from the edition of the standard that applies to your device (Chapter 4).
| Applied part | Normal condition | Single-fault condition |
|---|---|---|
| B, BF (body surface) | 100 µA | 500 µA |
| CF (cardiac) | 10 µA | 50 µA |
| DC, any type | 10 µA | — |
B.5The Open-BioAFE design in numbers
Table B.5. The main design values, with the chapter that sets each. Table 29.1 compares them with the specification.
| Block | Values | Chapter |
|---|---|---|
| LNA | chopped CCIA, Cin 20 pF, Cfb 200 fF, gain 40 dB, fch 4 kHz, NMOS input devices of 1000 µm² | 8–9 |
| Servo and boosting loops | 3.3 V integrator, CDSL 4 pF (noise gain 1.32); input impedance about 200 MΩ | 10 |
| Gain plan | ECG 100 × 1, EEG 100 × 8, EMG 10 × 8 onto ±0.5 V differential | 11 |
| Right-leg drive | loop gain 100 at 50 Hz, Ro 150 kΩ, 53° phase margin; CMRR-test residual 0.06 mVpp | 12 |
| SAR converter | 12-bit asynchronous, 14 cycles at radix 1.8, about 1 fF units, 4 pF per side, Vcm switching, seven low-noise comparator decisions, about 11.7 pJ per conversion, 16 kS/s shared by 8 channels | 15–18 |
| ΔΣ converter | second-order incremental, M = 1024 at 512 kHz, a1 0.5, a2 0.25, Cs 1.1 pF, 16.5 bits worst case, about 1.9 µW per channel | 19–20 |
| Reference | off-chip 1 µF reservoir capacitor | 17 |
| Budgets | noise 0.51 µVrms (wet) / 1.26 µVrms (dry); power 6.8 µW per channel (ECG/EEG), 4.9 µW (EMG); about 1.7 mm² of core | 29 |
B.6Constants
| Constant | Value |
|---|---|
| Boltzmann constant k | 1.380649 × 10⁻²³ J/K |
| Elementary charge q | 1.602177 × 10⁻¹⁹ C |
| Thermal voltage UT = kT/q | 25.9 mV at 300 K; 26.7 mV at 310 K |
| 4kT | 1.66 × 10⁻²⁰ J at 300 K; 1.71 × 10⁻²⁰ J at 310 K (body) |
| kT/C | 64 µVrms on 1 pF at 300 K |
| Mains | 230 V / 50 Hz or 120 V / 60 Hz |